You are not logged in. Please login or register.
SmoothVideo Project → Posts by Chainik
ok, set output to evr cp, start a video with the issue, press ctrl+j and post here the screenie
this's going to be interesting 
what if set output to overlay mixer?
The issue occurs with all files
with 1080p only or with any resolution sources?
Another test - turn off gpu acceleration in SVP
xioSlayer
set the "processing threads" value to 15 - will it change anything? if no then set it to 19...
you don't need to have different profiles for 29.97 and 30.00
oviano
newest NUC (Haswell i5, HD5000)
i5-4250U - slower than desktop i3 which is rather slow for HQ 1080p
it would be a 'double fps if 30 or below' option.
this's an easy part 
i believe it should work like this with default setting
anyway you always can add another video profile for high frame rate source and set to "do not interpolate"
However, do you know if MPC will use the original source fps before SVP has adjusted it or will it use the newly smoothed-up fps as the basis for switching the screen refresh rate?
I'm not sure but since SVP kicks in AFTER playback is started MPC should switch framerate before this.
Otherwise you can just set x2 interpolation mode and let MPC set the output refresh rate
reinstall video driver
oviano
Only thing I'm not sure about is what sort of hardware might be required.
Intel i5 + HD4600 or AMD FX-6xxx + any video card
I suppose it was also doing the decoding of the file aswell as the motion stuff
decoding is always hardware accelerated now so it's not an issue
anyway this device should pack captured video with some codec first before transfer to PC and I bet it's the same h.264
I think I'll give this a go and see what happens.
be sure you can return it to the seller 
Increase "motion vectors grid" value
May be.
If it's possible to process live DVB with SVP why can't work live video capture?
You just have to be sure it's possible to attach "ffdshow raw filter" to the chain (in PotPlayer).
MadVR smooth motion ?
Когда скачана? Я ее перевыкладывал в СБ.
I've all of "source" and "transform" filters checked on the "Internal filters" tab and only one "ffdshow raw" checked in "External filters" and it's all working as expected / as usual.
Check properties of "ffdshow raw" - it should be set to "Raw video" = "all supported" on the "Codecs" page.
what exactly "ain working"? ffdshow filter not loading or what?
630M is a very slow card, just do not put too much on it
well, try MPC-HC 1.7.xxx with LAV filters built-in
MPC-HC 1.7 has LAV built-in so you probably need to re-check / adjust filters (ffdshow raw) and LAV settings (set decoder to dxva copy-back) manually
assuming you have 60 HZ screen you can try to set "target frame rate" to "to screen refresh rate / 2" and "frames interpolation mode" to "1m"
you need to find PotPlayer's installation folder in the first "Select Executable..." dialog and select "PotPlayerMini.exe"
sausje
try latest "night" build of MPC-HC - http://nightly.mpc-hc.org/
let's start it over
You don't need to reinstall all software over and over or try to do the same on another machine. Also the fault isn't depends on available RAM size at all.
All you need is to run "4gb patch" manually and point it to "PotPlayerMini.exe". That's all.
Rimsky
там на картинке видно, что и 2015-й тоже
к кавери
только если 4-х модульный, что вряд ли
придется в конце концов прицениваться к интелю...
you can address this question to NV
generally - yes, SLI is supported by NV's OpenCL implementation
but it's just useless for SVP anyway
PotPlayer's binary (PotPlayerMini.exe) isn't patched for high memory consumption by default. Use "4GB patch" on it.
http://www.svp-team.com/wiki/FAQ#Video_ … time_error
("4gb patch" is included in SVP's full distro)
SmoothVideo Project → Posts by Chainik
Powered by PunBB, supported by Informer Technologies, Inc.