New RIFE filter - 3x faster AI interpolation possible in SVP!!! (Page 44 of 84)

if you're using default mpv, then no need to edit anything. The default is off.

if you're using SVP's mpv then go to C:\Program Files (x86)\SVP 4\mpv64
and edit the file mpv.conf

hwdec=auto-copy change to #hwdec=auto-copy. Just remove the "#" if you want to use it again.

I agree, they need to test it themself first if they see performance improvement or not.

In my case it's improvement.

But in some cases, if the CPU is so weak, the performance would drop a lot.

well, it costs you nothing to try, and can easily roll back.

simplest way to test is to use MSI Afterburner, and see the GPU power consumption graph.

in my case: 1080p24 + RIFE x3 + DXVA = 200W
1080p24 + RIFE x3 = 150W
lower GPU power consumption means it has more room for RIFE.

if anyone has a better way to test, let me know.

What happens when someone upload onnx packages for 4070 users? Will work for anyone who has the same GPU or not? I have v1/v2 prebuilt for HD/FHD sources with TRT boost enabled!
What about reverse engineering method for 4060Ti and 4060 owners too?
Average onnx build time v1 ~1/1.5 min HD/FHD
Average onnx build time v2 ~2/2.5 min HD/FHD

The RTX 4070 TensorRT performance (TRT boost enabled)
Model 4.4 (720p) singlethread 24>144 6x stable
Model 4.9 (720p) singlethread 24>120 5x stable
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
RIFE v2 models >
Model 4.4 (720p) singlethread 24>168 7x stable
Model 4.9 (720p) singlethread 24>144 6x stable
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Generally v2 models are 20% faster without noticeable intermediate frames quality drop, this peformance numbers achieved by single GPU thread, so you can go even higher, CPU utilization increase massively!
I dont recommend using more than 2 threads, but you can get upto 4x for 1080p videos easy!

V2 models faster

IDK

V2: faster, should use this as default if you not encountering any problems. model V2 47+ has a bug preventing you from using performance boost off.(It means it will run trt command on every video with a different resolution.)
4.13v1lite: lite is just a name, you may think of it as 4.135 which runs faster than 4.13
ensemble: this one will cost half the performance of the normal model. I couldn't see much difference from this, just use a better model instead.

try to use model in performance order: 4.6 > 4.9 > 4.13 lite > 4.13 and decide which one you like the most

4.9 is a sweet pot for me which has low artifact and runs faster than 4.13 20%

A v2 jaggedness/zigzag bug was fixed on 3 November: https://github.com/AmusementClub/vs-mlrt/issues/66
And the Rife devs re-uploaded the versions here: https://github.com/AmusementClub/vs-mlr … nal-models
Maybe try to redownload and check again if issue persists?

It was never a v2 issue, it was a model issue. The only v2 issue that has been recently fixed was lower quality output from source material over 2k.

This is correct. But some users may not have seen the issue depending on the videos they are watching. A good example of this effect is the Blade Runner 2029 intro with the patterned landscape. The zigzag artefact can be seen clearly just before the ship flies overhead with v4.6. but is minimised and only occurs once the ship flies over in v4.9. In v4.12 the artefact is gone.

Tested before your reply, my friend can use my generated files without troubles, same performance at all

Hi, I was trying to use Rife in the SVP. I've been only watching anime using SVP with non-RIFE settings since I purchased it which is 3 years ago.
I am totally clueless about these RIFE feature and tried to do my own research and test but was stuck at one thing, which shown as below:

The error "Your ONNX Model has been generated with INT64 weights, while TensorRT does not natively support INT64. Attempting to cast down to INT32."

After this message is shown, my playback will be stuck and only audio plays, sometimes even audio didn't play.

This is my setting for the RIFE

(that custom SC Threshold is because i tried following a youtube tutorial, but it still produced the same thing. Maybe I am doing it wrong)

I know there's probably an answer for this question already somewhere, I tried searching for it but there's too many too unrelated (probably) topic around it. a
I hope someone can guide me in getting Soap Opera effect using RIFE in SVP.
Sorry for the troubles and thanks for any consideration given.

-----------------------------------------------------------
Note that my pc setup is as such:

- Monitor 24" 144Hz
- AMD Ryzen 5 3600
- RTX 3080Ti 12GB
- 32GB DDR4 3200GHz ram
- around 500GB+ free space in the 1TB Adata S70 Blade M.2 NVme SSD

---------------------------------------------------------------
EDIT :

Nevermind, I am just too stupid. All i need to do is wait a bit longer and it'll works (using the settings in the picture)
But its weird, i swear i waited close to 30 mins before, hence I was thinking it's actually stuck/crashed. Now I just need to wait for 5 min at most.

Using MPC-HC since it has built-in fps counter. Would love to use MPV but I can't find the way to enable fps counter.